Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.
Blog Article
Do not take too lightly the forklift at the workplace. If the operation is bad, there will be severe mishaps in mins, and there are numerous mishaps entailing forklifts.
Case 1: The forklift freight blocked the motorist's view, and the individual in front could not be discovered, causing a moving crash.
Case 2: In order to maintain the equilibrium of the forklift when raising heavy items, the workers utilized their body weight as the weight, which nearly caused casualties.
Instance 3: The width of the forklift freight surpasses the allowable width of the route and hangs on the roadside rack, which virtually causes an crash.
Instance 4: Forklift is speeding and rolls over during a turn.
Case 5: The forklift motorist did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel illegally, the forklift driver does not wear the seat belt, the forklift lifter falls and the motorist is squashed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.
Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that hinder the safety and security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the motorist should initially confirm that the tons is stable and trusted.
4. The start has to be slow and constant.
Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the car to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are unique situations.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and have to maintain a particular safety and security range from the vehicle in front. .
7. When the forklift is running, the load must be in the most affordable position that does not prevent the driving, and the gantry should be properly tilted back. The lots will not be elevated other than when piling or packing. .
8. The height of the tons should not block the chauffeur's sight. In unique conditions, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for workers to base on the fork to hold items and play a stabilizing function. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will never operate with health problems or conceal them.
filling and discharging.
1. When fork-loading items, the range in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs should be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and hurt individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be kept in mind that the fork tip must not touch various other products or things. The load ought to be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and Electric Forklift Truck for Warehouse injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is Electric Forklift Truck for Warehouse not allowed to use forks to pick, turn pallet discharge.
Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is turned off and the power is cut off. (Except for special situations, such as the motorist does not leave the lorry's view and does not surpass 1 min).
4. Eliminate the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when declining;.
8. When the forklift workers carry the goods and move on, if they experience huge or heavy products and most likely to the motorist's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive laterally on inclines
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844